How to do tile paving, what are the steps?
In addition to the hydropower construction that everyone cares most about, it seems that it is very important to ask for the finest tile-laying work. It may be that the tile is usually put on the floor or wall with cement mortar. Yes, in fact, there are still many doorways. Then follow the decoration home network Xiaobian to learn about the relevant content!
1. Make a face clean on the wall before laying the tiles . Before the wall tiles are laid, the base layer needs to be cleaned first. The old paint on the wall needs to be removed first, then the interface is evenly brushed. The interface agent can fully wet the surface of the base layer, and improve the adsorption force of the plaster layer and the base layer to avoid wiping. The ash layer and the tile are hollowed out and fall off.
2, before laying the tiles , let it drink plenty of water. The fine voids inside the tile have a certain water absorption. Before the paving, the tile needs to be completely soaked, and the water is soaked until the surface no longer bubbles. The water is soaked to prevent it from absorbing the moisture of the cement mortar, causing empty drums and falling off. It is also the reason to sprinkle water on the wall before paving the wall. However, tiles with a water absorption rate of <0.5% are generally not required to be soaked.
3, pre-layout before paving, tiled to be flat. Before the tile is laid, it is necessary to pre-lay the paving in the construction space. If the pre-typesetting is not done, the color difference and the non-smoothing are likely to occur, and the sensory effect is poor. Generally, the height of the four corners should be within 0.5mm; the squareness of the yin and yang angle should be within 2mm; the verticality should be within 3mm; the flatness should be within 3mm.
4. Don't be too close between tiles. The seam of the tile is to avoid the force generated by the thermal expansion and contraction of the tile, to avoid the phenomenon of hollowing, arching and falling off, and to reduce the negative impact of the tile itself and the accuracy of the paving. You can take a fixed cross to get the card to improve the accuracy of the seam.
5, "wall pressure" is more durable and waterproof. It is best to use the "wall pressing" process for kitchen and bathroom tile paving. The brick wall has a large brick and small brick in the corner. In the large humidity room such as the bathroom kitchen, the wall brick pressing brick technology can ensure the condensation of water and gas to the wall. When it flows to the ground, it will not leak into the waterproof layer under the floor tiles, maximizing the service life of the waterproof layer. This kind of technology is used in the construction process of living in a variety of hard and hard construction. The wall brick floor tiles are more beautiful and practical, ensuring that there is no black corner and no sanitary corners in the kitchen and bathroom space.
6, "set of pressure stone" to make the bathroom door free of moisture. The use frequency of the bathroom is high and the water consumption is large. It is best to use the set of pressure stone technology. The stone in the door is 10-20mm higher than the bathroom floor. In addition, the door stone should be added with the ear ear technology to prevent the water vapor or water from directly entering the door cover. It is also carried out according to this standard during the construction process, which can effectively extend the service life of the door and protect the bathroom door from moisture.
The above is a detailed answer to the Xiaobian, I don't know if you are satisfied with the introduction of the decoration home network Xiaobian~ If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
What are the techniques for laying ceramic tiles?
Why don't Japanese people decorate their tiles? After listening to the reasons, I sigh that they are too smart.
More and more people decorate the bathroom, do not tile the floor, like to do so, bath drainage is fast and non-slip
What are the methods of laying tiles? Tiled precautions
The valve is a series of gas emergency Shut Off Solenoid Valves, specially designed as gas pipe breaker for emergency use. It can be connected with gas leaking detection sensor, fire alarm circuit or other intelligent sensor modules so that on site or remote shut down on gas supply (manually or automatically) is possible, hence ensuring the safety on gas usage. The valve features an auto-close when strong vibration is detected. After close, manual operation is required to turn on the valve. This feature meets safety regulations in the event of an accident.
Gas Solenoid,Solenoid Valve,Gas Solenoid Valve,Solenoid Operated Valve
Rictron Industrial Co , https://www.szrictron.com