Xiang Tian Explosion-proof: Explosion-proof floodlight use method and matters needing attention
Use <br> <br> determine where and how the lamp according to the actual needs of the job site, then the electrical power contacts to prepare Φ8 ~ Φ14mm three-core cable in accordance with the corresponding length of the lamp.
Open the end cap of ballast, loosen the pressing nut of the ballast cable inlet, and lead the lamp cable and power cable through the compression nut to the internal terminal of the ballast, connect and fix, and tighten separately. Cables tighten nuts and tighten ballast end caps.
According to the determined installation location and method, the lamps and ballasts are installed, and the other end of the input cable of the ballast can be connected to the 220V power supply according to the requirements of explosion-proof.
Loosen the screws at the bottom of the lamp holder bracket, and adjust the lighting position by rotating 360° around the lamp holder; loosen the screws on both sides of the lamp holder, adjust the lighting angle of the lamp holder up and down according to the lighting requirements, and then fasten the screws.
When replacing the lamp, use a suitable screwdriver or other tool to insert the front cover into the holes on the two front side of the front cover, remove the bad lamp, and replace the new one.
Note 1, the lamp is installed in the equipped carton during transportation, and foam shock absorption is added.
2. When installing and maintaining the lamp, you must disconnect the power supply.
3, when used, the surface of the lamp has a certain temperature rise, which is a normal phenomenon; the temperature of the center of the transparent part is relatively high and must not be touched.
4. When replacing the bulb, use the bulb of the same type and power; if you change the bulb type or power, replace the matching ballast accordingly.
BAT51 series explosion-proof floodlight (IIB) explosion-proof floodlight scope of application:
It is suitable for fixed flood light illumination in various flammable and explosive places such as gas stations, sea oil drilling platforms, tanker ships, chemical factories, and roads.
Performance characteristics:
The shell is made of high-quality aluminum alloy precision die-casting, high-pressure electrostatic spray after high-speed blasting on the surface, beautiful appearance and good corrosion resistance.
The lampshade is made of tempered glass. The exposed fasteners are made of stainless steel and can work normally for long periods in a humid and corrosive environment.
The reflector is designed with an orange-colored diffuse reflection, which softens the illuminance of light and slows down the eye fatigue of workers. It also increases the illumination angle of the lamp light source.
The light source and the electric appliance are integrated design. The light source cavity and the ballast are independent, and the side cover is opened, and the light bulb is replaced quickly to facilitate the installation and maintenance.
Technical Parameters
Rated voltage: AC220V50Hz
Light Source Type: High Pressure Mercury Lamp / High Pressure Sodium Lamp / Metal Halide Lamp Rated Power: 1000W
Explosion-proof mark: ExdeIICT4
Shell protection class: IP65
Anti-corrosion level: WF1
Cable outer diameter: ¢7～¢14mm
Insertion device thread: G3/4"
Dimensions: 560×420×360mm
Stellite Viscose Staple Rayon Fiber Cutter Blade
The Viscose Staple Rayon Fiber Cutter Blade is one of Cobalt Alloy (stellite alloy ) but it has Special chemical composition, it is widely used in textile industry , we have control the core technology to produce this kind of cutter blade through Powder Metallurgy . Its main advantages are corrosion resistance and wear resistance better than other material. We have loyal customers from domestic and abroad now and can provide different specifications blade for customers upon their request.
Our company has been focused on researching and developing the cobalt alloy for more than 20 years, most of our products are made through powder metallurgy, so we can produce high quality cutter blade with powder metallurgy and also control the cost to give best price to our customer and help them to save cost.
Cobalt Chrome Alloy Fiberglass Cutter Blade
Fiberglass Cutter Blade,Viscose Fiber Cobalt Chrome Alloy,Cobalt Chrome Alloy Cutter Blade,Viscose Fiber Cutter Blade
Shenyang New Industry Co.,LTD , https://www.topcobalt.com